The dynamic judgment method of reversing distance allows you to easily drive any model and quickly and accurately reverse

Click below to subscribe to the Beginner's Cheats Season 4 column to watch 50 episodes including this one

In the daily parking and reversing, it is necessary to make an effective judgment on the distance behind the car in the car, especially in the dynamic reversing, it is necessary to make a timely and accurate judgment, which can effectively improve the parking efficiency and parking accuracy.

Being able to develop a true sense of distance without the need for any auxiliary equipment will help you to handle any model in the future.

Today I will demonstrate the dynamic judgment method of reversing distance to teach you how to use your car to practice the sense of distance behind the car and be able to judge the distance quickly and accurately.

Hanging upside down gear start alternate observation of left and right rearview mirrors, alternating observation is to ensure that the body is in a vertical state when reversing, in the specific judgment distance can be based on your habit to observe the unilateral rearview mirror,

From the left and right side of the rearview mirror can be seen, the road shoulder edge along the alignment of the position of the body bumper gradually moved down, when the lower edge of the left and right sides of the body bumper and the road shoulder edge alignment, that is, feel the backwards, the rear bumper will begin to cover the road shoulder when the stop, the car under the actual measurement of this distance is how much.

Now the under-car surveyor uses a tape measure to measure the distance on the ground to see what is the actual distance from the rear bumper to the shoulder of the road? After measuring, the surveyor can be heard shouting out a distance of 1.5 meters,

Remember the change in the state of the picture seen in the rearview mirror and the state of rest when the last stop, which is the state of reversing from far and near, and finally stop to the state of 1.5 meters with the shoulder of the road.

After finding this sense of distance, you can drive the car forward for repeated reversing exercises until you really master the sense of distance in this reversing dynamic.

Let's continue to reverse to judge the closer distance. From the two side mirrors to see the rear bumper first cover the shoulder, and then the two sides of the rearview mirror began to appear different pictures, the left rearview mirror saw that the front door handle just covered a little shoulder, at this time the right front door handle is also just covered a little shoulder, but the left shoulder has moved down to the lower edge of the rearview mirror, and the right shoulder is still in the vertical third of the rearview mirror. This is not surprising, this is because the left rearview mirror looks far, so the adjustment is high, and the right rearview mirror looks close, so the adjustment is low.

Next by the car personnel to carry out field measurements, this time can obviously see that the distance has been relatively close, about 50 cm or so, OK, now the surveyor has shouted out the measured distance is 52 cm. This distance is a distance commonly used when parking in the parking lot, and everyone should focus on practicing it.

Then I fell backwards, fell to the limit distance to see how to judge, OK, now that I have reached the limit distance,

To measure whether there is a gap, the surveyor reports a distance of 5 centimeters, which has basically reached the limit, and will be used under extreme conditions.

Let's take a look at how the reversing process is observed, the left rearview mirror can no longer see the road shoulder, so rely on the right rearview mirror to judge, from the right rearview mirror, the road shoulder edge is gradually aligned to the middle of the front door handle. This distance has reached its limit, and it needs to be accurately mastered, and it is necessary to be as conservative as possible in actual operation.

Just demonstrated the reversing car to judge the distance, sometimes after reversing the car also need to go to the front of the car to adjust the distance, I will go one step further to see what is different. From the left rearview mirror, the road shoulder is gradually appeared in the rearview mirror, and the position of the road shoulder is half-cut high on the lower edge of the rearview mirror.

In the right rearview mirror, the farthest end of the front door handle is aligned with the curb edge, and then aligned with the curb shoulder wall.

Let's see what the difference between this distance and the 52 cm state when you just reversed. Or by the surveyor, after the field measurement, the surveyor reported the number is 92 centimeters. You can see that it is 40 centimeters different from the 52 centimeters just now.

However, the distance position seen in the rearview mirror is not large. This is because the picture seen in the rearview mirror is the result of n times smaller, and the angle is a side angle, not a front angle, so it is quite different from what you see intuitively outside. It is precisely because of this that this in the rearview mirror to judge the sense of distance to repeated practice and feeling, and finally to achieve a more accurate degree.

The above demonstration and actual measurement results will vary due to the model, height, sitting posture and rearview mirror adjustment habits, please focus on learning ideas and methods, and find your own points in practice to practice and use.

Dear old and new friends, a total of 50 videos of "Beginner Cheats - Season 4" have been updated